docs: second cross-ref pass (HvacMode/FanMode/HoldMode, pca_file, v1/connection)

Follow-up to 0d6465d, sprinkling pca-re/docs/manuals/ citations into
three more files that map to user-visible or installer-visible panel
behavior:

models.HvacMode / FanMode / HoldMode
  Docstrings now explain which values correspond to keypad menu picks
  vs. programmatic-only states, and point at the Owner's Manual
  *Scene Commands* chapter where each menu is laid out.

pca_file.py
  Module docstring adds Cross-references to the Installation Manual's
  *INSTALLER SETUP* chapter (SETUP CONTROL/ZONES/AREAS/MISC/EXPANSION)
  -- those are the keypad screens that produce the very SetupData /
  Names / Programs blocks the parser walks. Also points at APPENDIX C
  (zone and unit mapping) for where the _CAP_OMNI_PRO_II numbers come
  from on the panel side.

v1/connection.py
  Module docstring adds cross-references to the docs-site pages that
  explain (a) the non-public handshake quirks the v1 connection relies
  on for crypto and (b) why subsequent RequestUnitStatus calls need
  the long-form BE u16 payload (Appendix C zone/unit mapping again).

No code changes, doc-only; 387 tests still pass.

src/omni_pca/models.py

@@ -518,7 +518,13 @@ class SecurityMode(IntEnum):
 
 
 class HvacMode(IntEnum):
-    """Thermostat system mode (enuThermostatMode.cs)."""
+    """Thermostat system mode (enuThermostatMode.cs).
+
+    Values 0-3 match the keypad's "Thermostat → MODE" menu one-for-one
+    (Owner's Manual *Scene Commands → Thermostat Control* chapter,
+    pca-re/docs/owner_manual/06_Scene_Commands/). ``EMERGENCY_HEAT`` (4)
+    is heat-pump-only and not exposed in the standard keypad menu.
+    """
 
     OFF = 0
     HEAT = 1
@@ -528,7 +534,12 @@ class HvacMode(IntEnum):
 
 
 class FanMode(IntEnum):
-    """Thermostat fan mode (enuThermostatFanMode.cs)."""
+    """Thermostat fan mode (enuThermostatFanMode.cs).
+
+    Values 0-1 match the keypad's "Thermostat → FAN" menu (Owner's
+    Manual *Scene Commands*, 06_Scene_Commands/). ``CYCLE`` (2) is
+    programmable-only and not surfaced at the keypad.
+    """
 
     AUTO = 0
     ON = 1
@@ -538,8 +549,12 @@ class FanMode(IntEnum):
 class HoldMode(IntEnum):
     """Thermostat hold mode (enuThermostatHoldMode.cs).
 
-    Value 255 (``OLD_ON``) is a legacy "Hold" sentinel from older firmware
+    ``OFF`` / ``HOLD`` are the two states surfaced at the keypad's
-    that some panels still emit; treat it as equivalent to ``HOLD``.
+    "Thermostat → HOLD" menu (Owner's Manual *Scene Commands*,
+    06_Scene_Commands/). ``VACATION`` (2) is a programmable mode the
+    panel uses while a Vacation security mode is active. Value 255
+    (``OLD_ON``) is a legacy "Hold" sentinel from older firmware that
+    some panels still emit; treat it as equivalent to ``HOLD``.
     """
 
     OFF = 0

src/omni_pca/pca_file.py

@@ -16,6 +16,22 @@ References:
     clsPcaCfg.cs — keyPC01 / keyExport constants, PCA01.CFG layout
     clsHAC.cs:7943-8056 — .pca header + body walker, Connection block
     clsCapOMNI_PRO_II.cs — per-model size constants used by the body walker
+
+Cross-references (HAI OmniPro II Installation Manual):
+    *INSTALLER SETUP* (pca-re/docs/manuals/installation_manual/
+    04_INSTALLER_SETUP/) is what populates everything we then read back
+    from a .pca export:
+        SETUP CONTROL   → SetupData block (panel-wide options)
+        SETUP ZONES     → Names section (zone-name entries) + Z*_TYPE
+                          (encoded inside SetupData)
+        SETUP AREAS     → Names section (area-name entries) + per-area
+                          delays and codes in SetupData
+        SETUP MISC      → Programs section (timed scenes, energy savers)
+        SETUP EXPANSION → cap counters that drive how big each names
+                          block is on the wire
+    APPENDIX C — ZONE AND UNIT MAPPING (12_APPENDIX_C_-_ZONE_AND_UNIT_MAPPING/)
+    documents the address-space layout the cap constants in
+    _CAP_OMNI_PRO_II below derive from (176 zones, 511 units, etc.).
 """
 
 from __future__ import annotations

src/omni_pca/v1/connection.py

@@ -21,6 +21,14 @@ Reference: clsOmniLinkConnection.cs (UDP path):
     udpHandleRequestSecureSession lines 1461-1487 step 4 → OnlineSecure
     udpSend         lines 1514-1560  outer PacketType = OmniLinkMessage (16)
     EncryptPacket   lines 372-401    same crypto as TCP
+
+Cross-references:
+    *Two non-public quirks* — Owner's-Manual-style writeup of the
+    session-key XOR mix and per-block sequence whitening that this
+    handshake relies on: https://hai-omni-pro-ii.warehack.ing/explanation/quirks/
+    *Zone & unit numbering* — explains why subsequent ``RequestUnitStatus``
+    calls need the long-form (BE u16) payload for unit indices > 255:
+    https://hai-omni-pro-ii.warehack.ing/explanation/zone-unit-numbering/
 """
 
 from __future__ import annotations